ADHESIVES

Holding strong.
With system solutions that can do more.

2K PU 330

Solvent-free, flexible hardening 2-component adhesive based on polyurethane. Water-proof and weather-resistant. For use indoors and outdoors for laying high-load rubber, PVC, outdoors and sports facility coverings, as well as installation and repair adhesive for elastic adhesion of concrete, ceramics, stones and wood and many other building materials. Suitable for underfloor heating systems and castor wheel loads.

For Technical Data, click the icon below:

WET AND BONDING BED ADHESIVE D 391

Low-emission, solvent-free, odourless, high-quality dispersion adhesive.

Only indoors, for gluing homogeneous, PVC, floor and wall covering in tiles and membranes, as well as for textile floor coverings with latex smooth foam and latex stamped backs, latexed rear or PU foam backs.

Suitable for underfloor heating systems and for castor wheel loads.

For Technical Data, click the icon below:

DESIGN COVERING ADHESIVE D 495

Very low-emission, solvent-free, fibre-reinforced wet bed dispersion adhesive with high initial adhesion and hard adhesive grooves for increased dimensional stability requirements. Minimised residual indentation behaviour.

Only indoors for the adhesion of PVC, designer coverings and PVC-CV coverings in tiles and planks, rubber coverings in tiles and sheet up to 3.2 mm (over 3.2 mm after consultation) as well as chlorine-free floor covering (polyolefins). Suitable for underfloor heating systems and for castor wheel loads.

For Technical Data, click the icon below:

X-BOND MS-K499

Single-component special adhesive tested according to DIN EN 14259 on STP base for adhesion of LTV design covers, homogenous and heterogeneous PVC covers in membranes and tiles, CV coverings, rubber coverings in membranes and tiles (up to 10 mm, higher covering thicknesses in consultation), protective sluices, and artificial turf coverings. For the adhesion of absorbent and non-absorbent substrates indoors and outdoors. Specially formulated for raised thermal and mechanical load and/or increased wet load. The adhesive is also suitable for special rubber and recycling mats. 

For Technical Data, click the icon below:

QUICK ADHESIVE MORTAR FLEX WHITE SFK 81

White, almost temperature-independent, powdery, crystalline water binding, water and frostproof, highly tempered, hydraulically setting flexible adhesive mortar for laying up to 20 mm adhesive bed thickness. No show through for light materials.

For laying ceramic wall and floor tiles indoors and outdoors, panels, fine stoneware, natural stones for increased thermal or static loading in a layer thickness up to an adhesive thickness of 4 to 20 mm. Especially well suited for the laying of tiles on tiles and for large area boards and natural stones.

For Technical Data, click the icon below:

QUICK ADHESIVE MORTAR FLEX TRASS SFK 85

 

Near temperature-independent, powdery, crystalline water binding, water- and frostproof, highly tempered, rapid, hydraulically setting grey adhesive mortar for grouting in adhesive layer thicknesses up to 20 mm. The adhesive mortar offers more security against efflorescence and discolouration and can be used from +2 °C.

Indoors and outdoors for wall and floor area for laying of most varied ceramic files, mosaic, stoneware, split tiles, fine stoneware, clinker plates, handmade bricks, brick tiles, natural stones which are resistant to discolouration. Also for large formats as well as for adhesion of lightweight construction, glass fibre and hard foam boards and Murexin decoupling boards.

For Technical Data, click the icon below:

REPAIR ADHESIVE SK 15

Rapid setting special adhesive mortar for tiling in thin-bed process. Suitable for mixing with other adhesive through its special recipe.

For rapid improvement of individual tiles, for tiling or early loading areas as well as laying at colder temperatures. Especially to regulate the pot life through the addition of normal hardening adhesives.

Therefore, any desired processing time can be set by the installer.

For Technical Data, click the icon below:

UNIVERSAL FIXATION WL 720

Solvent-free, easy to process, rollable fixing.

Indoor use only for full area fixing of CV, PVC and textile coverings with smooth foam backings and self placing carpet tiles. Floor coverings can be fixed and are easy to remove again. Suitable for underfloor heating systems and castor wheel loads.

For Technical Data, click the icon below:

SPECIAL DESIGN COVERING ADHESIVE X-BOND MS-K499

Single-component special adhesive tested according to DIN EN 14259 on STP base for adhesion of LTV design covers, homogeneneous and heterogeneous PVC covers in membranes and tiles, CV coverings, rubber coverings in membranes and tiles (up to 10 mm, higher covering thicknesses in consultation), protective sluices, and artificial turf coverings. For the adhesion of absorbent and non-absorbent substrates indoors and outdoors. Specially formulated for raised thermal and mechanical load and/or increased wet load. The adhesive is also suitable for special rubber and recycling mats. In these instances, however, sample adhesions are required. For non-absorbent substrates, a relative air humidity of min. 50 % is required, as well as observing a corresponding flash-off time of approx. 10 -20 minutes .

For Technical Data, click the icon below:

MUREXIN-UK

System solutions that can do more.

Call Now Button